A handyman in Boston. Same day service

– Unpacked and laid out all parts, hardware, and tools.
– Attached the legs securely to the tabletop using pre-drilled holes.
– Assembled and installed the drawer, ensuring smooth glide on the track.
– Tightened all bolts and screws for a stable structure.
– Checked for level and made minor adjustments for balance.
– Cleaned the surface for a polished, finished look.

– Unboxed all panels, hardware, and organized
tools for easy access.
– Assembled the main frame, securing side
panels, base, and top.
– Installed interior shelving and hanging rods
according to layout.
– Mounted the doors and aligned hinges for
smooth, even closure.
– Tightened all connections and ensured
structural stability.
– Cleaned the exterior and interior for a
finished presentation.

– Unboxed and laid out all components,
including the bentwood frame, base supports,
and cushions.
– Assembled the curved wooden arms and
attached the cross-support base.
– Secured the seat frame tightly between the
armrests.
– Installed the cushioned seat and headrest
into the frame.
Tightened all bolts and fasteners for stability.
– Verified rocking motion and balanced
alignment.
– Wiped down the wood and leather to
complete the setup.

– Unpacked all parts and hardware, laying
everything out for quick access.
– Assembled the desk frame and secured the
legs to the desktop.
– Installed drawers or shelves (if included),
aligning tracks and fasteners.
– Tightened all screws and bolts to ensure
stability.
– Verified levelness and adjusted as needed.
– Wiped down all surfaces for a clean, ready-
to-use setup.

– Assembled high-back ergonomic gaming
chair with full lumbar and neck support.
– Installed seat base, backrest, and armrests
with reinforced hardware.
– Attached multi-function tilt mechanism and
gas lift for height adjustment.
– Secured five-star chrome base and installed
dual-wheel casters for mobility.
– Mounted adjustable pillows and tested
reclining/tilting functionality.
– Verified stability, smooth movement, and
user comfort post-assembly.d and leather to
complete the setup.

– Confirmed placement with the client and
measured optimal height and spacing.
– Marked anchor points precisely using a level
and measuring tape.
– Installed drywall anchors and screws
appropriate for the frame's weight.
– Mounted the artwork securely, ensuring
alignment and even spacing.
– Double-checked stability and made minor
adjustments for symmetry.
– Cleaned surrounding surfaces and removed
all installation residue.

– Inspected cabinet doors for sagging,
misalignment, or uneven gaps.
– Used precision screwdriver to adjust hinge
screws for vertical, horizontal, and depth
alignment.
– Ensured consistent spacing between doors
and flush closure across all units.
– Checked soft-close functionality and
corrected tension where needed.
– Cleaned hinge area and tested multiple
times for smooth, silent operation.

– Assessed door for sticking, uneven gaps, or
latch misalignment.
– Tightened or adjusted hinge screws to
reposition the door frame.
– Re-set or shimmed hinges as needed to level
the door vertically.
– Realigned the strike plate to ensure smooth
latching.
– Tested swing and closure multiple times,
fine-tuning for perfect fit.
– Verified flush gaps and noise-free operation.
Area left clean and undamaged.

– Inspected door frame for gaps, drafts, and
water entry points.
Removed old weatherstripping and cleaned
all contact surfaces thoroughly.
– Installed new high-density adhesive-backed
foam weatherstripping along the door jamb.
– Fitted a new door sweep to seal the gap at
the bottom edge.
– Applied exterior-grade silicone caulk around
the trim to prevent moisture penetration.
– Confirmed a snug, weather-tight seal
without affecting door function.

– Shut off water supply and removed the old
faucet and hardware.
– Cleaned mounting area and prepared sink
surface for new fixture.
– Installed the new faucet base and secured it
with mounting nuts.
– Connected hot and cold supply lines with
leak-free compression fittings.
– Turned water back on, tested pressure, and
ensured there were no leaks.
– Sealed edges with plumber's putty or
silicone for a clean, finished look.

– Located the damaged section and shut off
the water supply.
– Drained the line and inspected for cracks,
corrosion, or leaks.
– Cut out the damaged portion and prepped
pipe ends for replacement.
– Installed new pipe section or fitting using
appropriate connectors and sealants.
– Restored water flow and pressure-tested the
repair for leaks.
– Cleaned the area and ensured a secure,
long-lasting fix.

– Assembled the main cookbox and attached it
securely to the frame.
– Installed side panels, control knobs, and
stainless steel work surfaces.
– Connected burner tubes, igniters, and heat
shields for even flame distribution.
– Mounted lid with built-in thermometer and
ensured smooth opening/closing.
– Connected propane regulator and tested
ignition system.
– Completed with secure caster installation
and final safety checks.